92706 / 83005 ms pc b8-9060 no.a0078-1/9 la42352 overview la42352 is 5w 2-channel af power amplifier with dc volume control intended for televisions. la42000 series is power ic which made pin compatible possible altogether in 3 to 15w. they consist of four kinds of power ics. (mono, stereo, mono with volume function, stereo with volume function.). they realized pcb layout communalization of an audio power block of tv. channel po mono stereo volume la42051 5w la42052 5w la42351 5w la42352 5w la42071 7w la42072 7w LA42152 15w feature ? p o 5w 2ch (v cc = 18v, r l = 8 ? , thd = 10%) ? built-in dc volume control. ? built-in standby function. ? built-in overheat protection. ordering number : ena0078 monolithic linear ic 5w 2-channel af power amplifier with dc volume control any and all sanyo semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. consult with your sanyo semiconductor representative nearest you before using any sanyo semiconductor products described or contained herein in such applications. sanyo semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all sanyo semiconductor products described or contained herein.
la42352 no.a0078-2/9 specitications maximum ratings at ta = 25 c parameter symbol conditions ratings unit maximum supply voltage v cc max no signal 24 v allowable power dissipation pd max infinite heat sink 15 w maximum junction temperature tj max 150 c thermal resistance jc 3 c/w operating temperature topr -25 to +75 c storage temperature tstg -40 to +150 c operating conditions at ta = 25 c parameter symbol conditions ratings unit recommended supply voltage v cc 18 v recommended load resistance r l 8 ? allowable operating voltage range v cc op 10 to 22 v operating characteristics at ta = 25 c, v cc = 18v, r l = 8 ? , volume = 5v, f = 1khz, rg = 600 ? ratings parameter symbol conditions min typ max unit standby current i stb amplifier off 1 10 a quiescent current i cco rg = 0, volume = 0v 35 65 130 ma output power p o thd = 10% 4 5 w total harmonic distortion thd p o = 1w 0.1 0.8 % voltage gain vg v o = 0dbm 32.5 34.5 36.5 db output noise voltage v no rg = 0, volume = 0v, bpf = 20hz to 20khz 0.13 0.4 mvrms volume attenuation att v in = 100mv, vcont = 0v, with 1k-bpf 70 80 db channel separation sep. rg = 10k ? , v o = 0dbm 48 55 db v stb -h amplifier on 2.5 10 v standby control voltage (the pin 5 voltage) v stb -l amplifier off 0 0.5 v input resistance ri 14 20 26 k ? *0dbm = 1mw (600 ? ) = 774.6mvrms package dimensions unit : mm 3107b
la42352 no.a0078-3/9 block diagram sample application circuit ripple filter block thermal protection circuit out p ut am p lifier in p ut am p lifier out p ut am p lifier in p ut am p lifier 5 standby 7 v cc ri = 20k ? in1 2 volume 1 13 pre gnd 3 in2 4 volume 2 6 ri = 20k ? ripple filter 1 nf2 9 out2 8 power gnd 10 nf1 11 out1 12 c3 47 f /25v la42352 r l r l ripple filter 1 in1 2 pre gnd 3 c1 1.0 f /10v in2 4 stb 5 vol 2 6 c2 1.0 f /10v cpu v cc 7 out2 8 c4 1000 f /25v r3 10k ? c7 0.1 f r1 2.2 ? +5v nf2 9 c9 47 f /16v c5 470 f /16v pwr gnd 10 nf1 11 out1 12 vol 1 13 c10 47 f /16v c8 0.1 f r2 2.2 ? c6 470 f /16v +5v + + + + + + + +
la42352 no.a0078-4/9 pin descriptions pin voltage pin no symbol v cc = 18v equivalent circuit description 1 rf 17.6 ? ripple filter reference 2 4 in1 in2 4.4 ? input pin 3 pre_gnd 0 ? pre gnd pin 5 stb 0 to 5v (input voltage) ? standby pin ? the standby function is on when this pin at ground level 6 13 vol 2 vol 1 0 to 5v (input voltage) ? control volume 7 v cc 18 ? power supply continued on next page.
la42352 no.a0078-5/9 continued from preceding page. pin voltage pin no symbol v cc = 18v equivalent circuit description 8 12 out2 out1 8.9 ? output pin 9 10 nf2 nf1 8.8 ? negative feedback pin at power amplifier ? connect nf capacitor 10 pwr_gnd 0 ? power gnd pin description of external parts c1, c2 : input capacitors. a value of 1.0 f is recommended for capacitors. note that the low-frequency area characteristics can be ad justed by changing f l . c3 : ripple filter capacitor. a value of 47 f is recommended for capacitors. decreasing the capacitance value excessively or removing this capacitor causes ripple to occur. however, increasing the capacitance value does not always cause ripple to reduced. decreasing the capacitance value makes the starting time earlier. c4 : power capacitor. c5, c6 : output capacitors. a value of 470 f is recommended for capacitors. c7, c8 : oscillation blocking capacitor. use a polyester film capacitor that is good in high frequency response and temperature characteristic. c9, c10 : feedback capacitor. a value of 47 f is recommended for capacitors. decreasing the capacitance value lowers the low frequency response. increasing the capacitance value makes the starting time later. r1, r2 : resistor connected in series with oscillation bloc king capacitor. prevents phase shift attributable to the oscillation blocking capacitor so that oscillation is hard to occur. r3 : standby switch current limiting resistor. a value of 10k ? is recommended for resistance (when the applied voltage for the standby switch is 3v to 10v). this resistor cannot be removed.
la42352 no.a0078-6/9 features of ic inside and usage note standby function ? pin 5 is the standby switch pin. the amplifier is turned on by applying approximately 3v or more to this pin through an external resistor (r3). ? if voltage in excess of 10v is to be applied to the standby switch, calculate the value of r3 using the following formula so that the current flowing into pin 5 is 500 a or less: r3 = (applied voltage ? 2v be ( 1.4v)) 500 a ? 15k ? protector ? in order to prevent damage or degradation which may be caused by abnormally heated ic, the la42352 has a thermal shutdown protector. accordingly, if the ic junction temperature (tj) climbs to around 160 c due to inadequate heat dissipation, the thermal shutdown protector will operate to control the output gradually into attenuation.
la42352 no.a0078-7/9
la42352 no.a0078-8/9
la42352 no.a0078-9/9 ps specifications of any and all sanyo semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. sanyo semiconductor co., ltd. strives to supply high-quality high-reliability products. however, any and all semiconductor products fail with some probability. it is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. when designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. in the event that any or all sanyo semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of sanyo semiconductor co., ltd. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equipment, refer to the "delivery specification" for the sanyo semiconductor product that you intend to use. information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. sanyo semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. this catalog provides information as of august, 2005. specifications and information herein are subject to change without notice.
|
